Delta >
Delta 4380-AR-DST Pilar Single-Handle Kitchen Faucet With Spray
Discontinued
Description:
- Meets standards set by Americans with Disabilities Act
- Includes convenient side sprayer
- 3-hole 6-16 in. installation
- High-arc spout swivels 180-degree for greater convenience
- 45 in. long hose provides outstanding reach
- 1.80 gpm @ 60 psi, 6.8 L/min @ 414 kPa
- Lifetime Faucet and Finish Warranty
Specification:
- Brand:
- Delta
- Guides & Documents:
-
Spec Sheet
Installation Sheet - Stock Status:
- In Stock
- Number of Handles:
- 1
- Collection:
- Pilar
- Color:
- Arctic Stainless
- Spout Height (in):
- 13
- Spout Reach (in):
- 10.5
- Flow Rate (GPM):
- 1.8
- Color/Finish Family:
- Stainless Steel Tones
- Valve Type:
- DIAMOND(TM) Seal Valve
- Country of Origin:
- USA
- Aerator Type:
- Cache
- arctic stainless:
- /delta-4380-ar-dst
- chrome:
- /delta-4380-dst
- venetian bronze:
- /delta-4380-rb-dst
Reviews:
28 Reviews
-
I received the kitchen facet two days after I ordered it. I didn't expect it for at least a week Delta 4380-DST Arctic Stainless Pilar Kitchen Faucet with Side Spray - Includes Lifetime Warranty<p><small>Originally Posted on DeltaFaucet.com</small></
I received the kitchen facet two days after I ordered it. I didn't expect it for at least a week Delta 4380-DST Arctic Stainless Pilar Kitchen Faucet with Side Spray - Includes Lifetime Warranty<p><small>Originally Posted on DeltaFaucet.com</small></p>
-
For the most part, we are happy with this faucet. The reservation is with the aeration. The stream of water comes out almost as if there were no aeration at all, and there is a lot of splashing as the stream of water hits whatever is under the tap. C
For the most part, we are happy with this faucet. The reservation is with the aeration. The stream of water comes out almost as if there were no aeration at all, and there is a lot of splashing as the stream of water hits whatever is under the tap. Causes too much water spread. For the relative cost of this set, it is unsatisfactory. Other faucets I have owned did a much better job in this regard, and one could hold something under the tap without getting water everywhere.<p><small>Originally Posted on DeltaFaucet.com</small></p>
-
I love the bronze color and the height of the faucet. It is a beautiful addition to my kitchen décor.<p><small>Originally Posted on DeltaFaucet.com</small></p>..
I love the bronze color and the height of the faucet. It is a beautiful addition to my kitchen décor.<p><small>Originally Posted on DeltaFaucet.com</small></p>
-
During a 2005 kitchen remodel we chose a Delta high-arc spout faucet and sprayer for both the main farmhouse sink (along with a soap dispenser) and on the secondary prep/bar sink (in the coordinating smaller spout size). After just a few years, the m
During a 2005 kitchen remodel we chose a Delta high-arc spout faucet and sprayer for both the main farmhouse sink (along with a soap dispenser) and on the secondary prep/bar sink (in the coordinating smaller spout size). After just a few years, the main faucet had to be replaced and we sadly found that the original spout design had been discontinued. Even though the closest replacement faucet had a different spout angle and design than the original (so now it doesn't match the one on the prep/bar sink), we resolved that it was "close enough" and chose to stay with Delta. Overall we've been happy with the performance and quality. Frustratingly, the soap dispenser bottle has broken for now the 2nd time. The first time the plastic bottle cracked/broke where the neck meets the body. This time, the top threads of the replacement bottle (installed 8/9/13) have broken off inside the nut/countertop mount. My husband was able to back-out the broken threads from inside the nut but we now need a new (3rd) soap dispenser bottle. Separately, we also need to replace a broken plastic piece from inside of the handle/lever sleeve assembly. The broken piece is a threaded black, 4-tabbed plastic piece that screws onto the top of the valve assembly. That black, 4-tabbed plastic piece serves to position/seat the finished metal sleeve/cover (which has corresponding notches to align with the tabs of the black, 4-tabbed plastic piece). With one of the black plastic tabs broken, the finished metal sleeve/cover now spins beneath the handle. Lastly the red/blue button plug that covers the set-screw also needs replaced. I've attached photos and would appreciate help with the needed parts replacement. Overall, the performance of the faucets has been excellent; just failure of some plastic pieces.<p><small>Originally Posted on DeltaFaucet.com</small></p>
-
My only gripe is the low flow rate of the faucet..<p><small>Originally Posted on DeltaFaucet.com</small></p>..
My only gripe is the low flow rate of the faucet..<p><small>Originally Posted on DeltaFaucet.com</small></p>
-
Looks great. Only problem is that we've already had to call the plumber who installed it back to fix a.faulty mount.<p><small>Originally Posted on DeltaFaucet.com</small></p>..
Looks great. Only problem is that we've already had to call the plumber who installed it back to fix a.faulty mount.<p><small>Originally Posted on DeltaFaucet.com</small></p>